ICC-ES Criteria for Reference Only
The criteria listed below may serve as the basis for an ICC-ES legacy report, or were issued and have been withdrawn, but they do not address current editions of the International Codes. They may be used as reference for the development of new ICC-ES acceptance criteria (or a revised ICC-ES acceptance criteria if they include older editions of the International Codes).
- (AC06) Solid-fuel-burning Heating Appliances
- (AC08) Concrete Tile Underlayment on Spaced Sheathing
- (AC20) Residential Chimney Liners
- (AC26) Extended Set Control Chemical Admixture System
- (AC28) Class 5 Ducts Conveying Nonflammable Corrosive Fumes And Vapors
- (AC34) Prefabricated Fireboxes
- (AC35) Grease Duct Enclosure Systems
- (AC40) Sandwich Panels of Natural Stone Backed With Reinforced Epoxy Resin
- (AC41) Ductile Connectors In Precast Concrete Special Moment Resisting Frames
- (AC45) Type I Structural Silicone Glazing Sealants (Adhesive)
- (AC62) Disodium Octaborate Tetrahydrate (DOT) Wood Preservative Treatment Systems
- (AC64) Aluminum Siding
- (AC67) Ceiling Systems Incorporating Decorative Foam Plastic Molding
- (AC68) Glass Block Masonry Construction
- (AC78) Copper-quaternary and Copper-zinc Wood Preservative Treatment Systems
- (AC79) Skylights with Plastic Frames
- (AC82) Phenolic Gypsum Core Panels Used as Exterior Wall Coverings
- (AC83) Plastic Panels for Walls of Water Closet Compartments and Showers
- (AC84) Testing of Fire Doors and Windows under Positive Pressure
- (AC89) Laboratory Accreditation (for current issue see www.iasonline.org)
- (AC91) Foamed-cement Wall Systems
- (AC94) Product Specific Wood Shake and Shingle Roof Systems
- (AC95) Test Method to Determine Bending Yield Moment of Nails
- (AC96) Grading of White Spruce, Black Spruce and Lodgepole Pine Tapersawn Shakes
- (AC97) Insulated Garage Doors with Foam Plastic Cores
- (AC98) Quality Control Agency Accreditation (for current issue see www.iasonline.org)
- (AC103) Unvented Decorative Gas Logs
- (AC110) Cellular (Foamed) Thermoplastic Trim Molding
- (AC111) Composite Rubber Hose and Fittings for Use in Hydronic Heating Systems
- (AC112) Cross-linked Polyethylene (Pex) Tube And Fittings For Use In Hydronic Heating Systems
- (AC117) Wall And Roof Systems With Foamed-cement
- (AC119) Adhesively Attached Drywall Tape
- (AC121) Grease Duct Systems, Self-enclosed
- (AC123) Conformity Assessment Program
- (AC127) Roofing Systems with Asphalt Shingles Made with Glass Felt
- (AC128) Smoke Control Gasketing
- (AC134) Foamed Clay Roofing Systems
- (AC135) Snow Load Design Calculation Procedures of the 1995 National Building Code of Canada as an Alternate to Those in the 1997 Uniform Building Code
- (AC137) Clinched Connections of Cold-formed Steel Structural Members
- (AC139) Fittings for PEX Tubing
- (AC141) Antenna Enclosure Systems
- (AC142) Foam Plastic Insulation Applied Directly to Steel Decks
- (AC143) Copper-azole Wood-preservative Treatment Systems
- (AC145) Expansion Anchors in Steelwork Connection and Suspension Systems
- (AC146) Roofing Systems Steel-reinforced Rubber Shakes
- (AC150) Plastic Partitions Used in Public Restroom and Similar Facilities
- (AC153) Forced Combustion-Air System
- (AC158) Nonpaper-faced Fiber-reinforced Gypsum Panels Used as an Alternate to Gypsum Board
- (AC163) Prefabricated Septic Tanks
- (AC164) Quality Control Requirements for Surplus Concrete Used to Construct Retaining Wall Blocks
- (AC172) Fabricators of Structural Welding
- (AC190) CCA Type C Wood-preservative Treatment
- (AC242) Waterborne Copper Naphthenate Wood Preservative
- (AC254) PXTS Wood Preservative
- (AC268) Organic Wood Preservative Systems
- (AC297) Acetylated Wood Preservative Systems
- (AC314) DCOIT Wood Preservative Systems
- (AC329) Waterborne Copper Oxide, Boric Acid and HDO Wood Preservative Systems
 |